Huawei S5731-S24T4X 10GE uplink 24 port gigabit aggregation switch CloudEngine Technical specifications Item Description Memory (RAM) 2 GB Flash 1 GB in total. To view the available flash memory size, run the display version command. Mean time between failures (MTBF) 57.73 years Mean time to repair (MTTR) 2 hours Availability gt, 0.99999 Service port surge protection Common mode: plusmn,6 kV Power supply surge protection Using AC power modules: plusmn,6 kV in differential mode, plusmn,6 kV in common mode Using DC power modules: plusmn,2 kV in differential mode, plusmn,4 kV in common mode Dimensions (H x W x D) Basic dimensions (excluding the parts protruding from the body): 43.6 mm x 442.0 mm x 420.0 mm (1.72 in. x 17.4 in. x 16.5 in.) Maximum dimensions (the depth is the distance from ports on the front panel to the handle on the rear panel): 43.6 mm x 442.0 mm x 448.0 mm (1.72 in. x 17.4 in. x 17.7 in.) Weight (with packaging) 8.4 kg (18.52 lb) Stack ports 10GE SFP+ ports on the front panel RTC Supported RPS Not supported PoE Not supported Rated voltage range AC input: 100 V AC to 240 V AC, 50/60 Hz High-Voltage DC input: 240 V DC DC input: -48 V DC to -60 V DC Maximum voltage range AC input: 90 V AC to 290 V AC, 45 Hz to 65 Hz High-Voltage DC input: 190 V DC to 290 V DC DC input: -38.4 V DC to -72 V DC Maximum power consumption (100% throughput, full speed of fans) 114 W Typical power consumption (30% of traffic load, tested according to ATIS standard) 88 W Operating temperature -5C to +45C (23F to 113F) at an altitude of 0-1800 m (0-5906 ft.) NOTE: When the altitude is 1800-5000 m (5906-16404 ft.), the highest operating temperature reduces by 1C (1.8F) every time the altitude increases by 220 m (722 ft.). The switch cannot be started when the ambient temperature is lower than 0C (32F). S5731-S24T4X (02353AHU-001 or 02353AHU-002) appearance. 1 Twenty-four 10/100/1000BASE-T ports 2 Four 10GE SFP+ ports Applicable modules and cables: GE optical module GE-CWDM optical module GE-DWDM optical module GE copper module (100M/1000M auto-sensing) 10GE SFP+ optical module (OSXD22N00 not supported) 10GE-CWDM optical module 10GE-DWDM optical module 1 m, 3 m, 5 m, and 10 m SFP+ high-speed copper cables 3 m and 10 m SFP+ AOC cables 0.5 m and 1.5 m SFP+ dedicated stack copper cables (used for zero-configuration stacking) 3 One console port 4 One ETH management port 5 One USB port 6 One PNP button NOTICE: To restore the factory settings and reset the switch, hold down the button for at least 6 seconds. To reset the switch, press the button. Resetting the switch will cause service interruption. Exercise caution when you press the PNP button. 7 Ground screw NOTE: It is used with a ground cable. 8 Fan module slot 1 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust)) 9 Fan module slot 2 NOTE: Applicable fan module: FAN-023A-B (Fan box(B,FAN panel side exhaust)) 10 Power module slot 1 NOTE: Applicable power module: PAC600S12-CB (600 W AC Power Module) PAC600S12-EB (600 W AC Power Module) PAC600S12-DB (600 W AC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module) PAC150S12-R (150 W AC Power Module) PDC180S12-CR (180 W DC Power Module) (applicable in V200R020C00 and later versions) 11 Power module slot 2 NOTE: Applicable power module: PAC600S12-CB (600 W AC Power Module) PAC600S12-EB (600 W AC Power Module) PAC600S12-DB (600 W AC Power Module) (applicable in V200R020C10 and later versions) PDC1000S12-DB (1000 W DC Power Module) PAC150S12-R (150 W AC Power Module) PDC180S12-CR (180 W DC Power Module) (applicable in V200R020C00 and later versions) - -
