Cisco WS-X45-SUP7-E Supervisor Engine Catalyst 4500-E Series Overview WS-X45-SUP7-E, the Cisco Catalyst 4500E supervisor engine 7-E, is the leading borderless networks access and aggregation supervisor engine for the Cisco Catalyst 4500E series. Supervisor Engine7-E delivers high-performance aggregation deployments with increasing Gigabit Ethernet and 10G Ethernet fiber density along with hardware capabilities to support enterprise-level aggregation functions. Notice that WS-X45-SUP7-E= is similar with WS-X45-SUP7-E, except that WS-X45-SUP7-E= is a spare one. Specifications: WS-X45-SUP7-E Specification Chassis compatibility All Catalyst 4500 E-series switches Software requirements (minimum) Refer to your software release notes for the latest software release requirements Chassis slot restrictions Catalyst 4503-E: Slot 1 only Catalyst 4506-E: Slot 1 only Catalyst 4507R-E and Catalyst 4507R+E: Slot 3 and slot 4 Catalyst 4510R-E and Catalyst 4510R+E: Slot 5 and slot 6 Bandwidth per slot 48-Gbps Memory 2-GB (upgrade to 4-GB) STATUS LED The status LED indicates the current health of the supervisor engine and the current software state. RESET switch The RESET switch is used to reset and restart the switch. Note Use a paper clip or other small, pointed object to press the RESET switch. ACTIVE SUP LED The active supervisor engine LED indicates whether the supervisor engine is active or in standby mode in redundant supervisor engine configurations. UTILIZATION LEDs Eight LEDs indicate (as an approximate percentage) the current traffic load over the backplane. USB connectors Two USB 2.0 ports are provided. Port 1 operates in device mode (upstream) and port 2 in host mode (downstream). Port 1 has a standard Type B USB connector and can be used as a USB console.Port 2 has a USB type A connector and a standard USB 2.0 device like a flash memory device can plug into this connector. SECURE DIGITAL slot A standard Secure Data (SD) memory card interface is provided on the front panel CONSOLE port This is a 10/100/1000 port that uses an RJ-45 connector. The console port allows you th access the switch either locally (with a console terminal) has an RJ-45 connector. The console port allows you to perform the following functions: Configure the switch from the CLI Monitor network statistics and errors Configure SNMP agent parameters 10/100/1000 MGT port The Ethernet management port is a Layer 3 host port to which you can connect a PC. You can use the Ethernet management port instead of the switch console port for network management. When managing a switch, connect the PC to the Ethernet management port on a Catalyst 4500 E-series switch. Note When connecting a PC to the Ethernet management port, you must assign an IP address. LINK LED The 10/100/1000 MGT port has a link LED associated with it. 1G/10G UPLINKS (SFP/SFP+) ports The Supervisor Engine 7-E has four 1-G or 10-G ports that use either SFP transceivers or SFP+ transceivers. Uplink port LEDs Each of the four uplink ports has two LEDs associated with it. One LED displays port status when a 1-GB SFP transceiver is installed in the port socket. The second LED displays uplink port status when a 10-GB SFP+ transceiver is installed in the port socket. Power requirement 302 W Operating temperature Certified for operation: 32 to 104F (0 to 40C) Designed and tested for operation: 32 to 130F (0 to 55C) Humidity (RH) ambient (noncondensing) 10 to 90% Operating altitude Certified for operation: 0 to 6500 ft (0 to 2000 m) Designed and tested for operation: -200 to 10,000 ft (-60 to 3000 m) Operating temperature Certified for operation: 32 to 104F (0 to 40C) Designed and tested for operation: 32 to 130F (0 to 55C) Other related products: WS-X4448-GB-RJ45 WS-X4548-GB-RJ45 WS-X4548-GB-RJ45V WS-X6148A-GB WS-X6148A-GE-TX WS-X6148A-GE-45AF WS-X6148-GE-TX WS-X6516A-GBIC WS-X6548-GE-TX WS-X6704-10GE WS-X6704-10GE WS-X6708-10GE-3CXL WS-X6724-SFP WS-X6748-GE-TX If you have any questions about cisco poducts or want to know more the other cisco products, please do not hesitate to contact with Dannis Hu. Skype: lonrisesales02 Email: dannis(at)lonriseeqt.com Tel: 86 13601984814
