Cisco SPA Card SPA-2XOC48POS/RPR 2-port OC48/STM16 POS/RPR Shared Port Adapters SPA-2XOC48POS/RPR Overview SPA-2XOC48POS/RPR is the Cisco Router Shared Port Adapter. This Cisco 1-, 2-, and 4-Port OC-48c/STM-16c POS/RPR SPAs are available on high-end Cisco routing platforms and offers the benefits of network scalability with lower initial costs and easy upgrades. The SPAs continues the Cisco focus on investment protection along with consistent feature support, broad interface availability, and leading-edge technology. The SPAs allow different interfaces (POS, ATM, etc.) to be deployed on the same carrier card. SPA-2XOC48POS/RPR Specification SPA-2XOC48POS/RPR Specifications Type Cisco Router Shared Port Adapter Product Compatibility Cisco Catalyst 6500 Series Switches Cisco 7600 Series Routers Cisco 12000 Series Routers Cisco XR 12000 Series Routers Cisco ASR 1000 Series Router Cisco ASR 9000 Series Router(2 port only) Cisco CRS Carrier Routing System(2 and 4 port only) Port Density per SPA 1, 2, and 4 ports Physical Interface OC-48c/STM-16c SFP optics module (see optical parameters below) Visual status indicators (LEDs) SPA status LED Per port LEDs Carrier/Alarm Active/Loopback Protect (DPT/RPR mode) Pass Through (DPT/RPR mode) Protocols (see table below for RPR/SRP support info) High-Level Data Link Control (HDLC), RFC 2615 Point-to-Point Protocol (PPP), RFC 1662 Frame Relay, RFC 2427 IPv4/IPv6 IEEE 802.17 - Resilient Packet Ring (RPR) IETF 2892 - Spatial Reuse Protocol (SRP) Features and Functions Synchronization Local (internal) or loop timed (recovered from network) Stratum 3 clock accuracy (plusmn, 4.6 ppm) over full operating temperature Pointer activity monitoring Local (diagnostic) and line (network) loopback Section DCC (SDCC) - Platform-dependent feature Payload mapping 1 + X^43 self-synchronous scrambler SONET/SDH compliance Telecordia (Bellcore) GR-253-CORE (as applicable) ANSI T1.105, T1.231 ITU-T G.707, G.957, G.825 (as applicable) Supported SONET/SDH alarm and signal events Signal Failure Bit Error Rate (SF-BER) Signal Degrade Bit Error Rate (SD-BER) Signal Label Payload Construction (C2) Path Trace Byte (J1) Section Loss of Signal (LOS) Loss of Frame (LOF) Error Counts for B1 Threshold Crossing Alarms (TCA) for B1 Line Line Alarm Indication Signal (LAIS) Line Remote Defect Indication (LRDI) Line Remote Error Indication (LREI) Error Counts for B2 Threshold Crossing Alarms (TCA) for B2 Path Path Alarm Indication Signal (PAIS) Path Remote Defect Indication (PRDI) Path Remote Error Indication (PREI) Error Counts for B3 Threshold Crossing Alarms (TCA) for B3 Loss of Pointer (LOP) Positive Stuffing Event (PSE) Negative Stuffing Event (NSE) Path Unequipped Indication Signal (PUNEQ) Path Payload Mismatch Indication Signal (PPLM) Network Management RFC 2558 MIB (SONET/SDH) Simple Network Management Protocol (SNMP) Reliability and Availability Online insertion and removal (OIR) Field-replaceable SFP optical modules 1+1 SONET Automatic Protection Switching (APS) and SDH Linear Multiplexer Section Protection (MSP) protocols Single SPA software reset Physical Specifications Weight: 0.75 lbs (0.34 kg) Height: 0.8 inches (2.03 cm) Width: 6.75 inches (17.15 cm) Depth: 7.28 inches (18.49 cm) Power 18 Watts maximum (4-port) 15.5 Watts maximum (1-, 2-, and 4-Port) 12 Watts maximum (1-port) Environmental Specifications Operating temperature: 41 to 104F (5 to 40C) Storage temperature: -38 to 150F (-40 to 70C) Operating humidity: 5 to 85% relative humidity Storage humidity: 5 to 95% relative humidity Compliance and Agency Approvals Safety UL 60950 CSA 22.2-No.60950 EN60950 IEC 60950 CB Scheme ACA TS001 AS/NZS 3260 EN60825IEC60825 laser safety (SR, IR-Class 1) (VSR-Class 1M)1 21CFR1040 -FDA Code of Federal Regulations (USA) laser safety (SR, IR-Class 1) (VSR-Class 1M)1 EMC FCC Part 15 (CFR 47) ICES 003 EN55022 CISPR 22 AS/NZ 3548 VCCI EN55024 EN50082-1 EN61000-6-1 EN61000-3-2 EN61000-3-3 Network Equipment Building System (NEBS) This product is designed to meet the following requirements (official qualification may be in progress): SR-3580 - NEBS: criteria levels (Level 3 compliant) GR-63-Core - NEBS: physical protection GR-1089-Core - NEBS: EMC and safety European Telecommunications Standard Institute (ETSI) EN300 386/EN300 386-2 Class B ETS 300 019 Storage Class 1.1 ETS 300 019 Transportation Class 2.3 ETS 300 019 Stationary Use Class 3.1 The Cisco Interface Flexibility (I-Flex) design combines shared port adapters (SPAs) and SPA interface processors (SIPs) to help enable service prioritization for voice, video, and data services. Enterprise and service provider customers can take advantage of improved slot economics resulting from modular port adapters that are interchangeable across Cisco routing platforms. The extensible Cisco I-Flex design maximizes connectivity options and offers superior service intelligence through programmable interface processors that deliver line-rate performance. Cisco I-Flex enhances speed-to-service revenue and provides a rich set of quality of service (QoS) features for premium service delivery while effectively reducing the overall cost of ownership. This data sheet contains the specifications for the Cisco 1-, 2-, and 4-Port OC-48c/STM-16c Packet over SONET/SDH (POS) and Resilient Packet Ring (RPR) Shared Port Adapter (Cisco 1-, 2-, and 4-Port OC-48c/STM-16c POS/RPR SPA, ) Business
