Cisco C9200L-24P-4X-E Catalyst 9200L 24-P PoE+ 4x10G Network Essentials C9200L-24P-4X-E is the Catalyst 9200L 24 ports full PoE+ 4x10G uplink Switch, with Network Essentials software. Cisco Catalyst 9200 Series switches extend the power of intent-based networking and Catalyst 9000 hardware and software innovation to a broader set of deployments. With its family pedigree, Catalyst 9200 Series switches offer simplicity without compromise it is secure, always on, and IT simplified. Model C9200L-24P-4X-E Downlinks total 10/100/1000 or PoE+ copper ports 24 ports full PoE+ Uplink configuration 4x 10G fixed uplinks Default primary AC power supply PWR-C5-600WAC Fans Fixed redundant Software Network Advantage Stacking bandwidth 80 Gbps DRAM 2 GB Flash 4 GB Switching capacity 128 Gbps Forwarding rate 190.4 Mpps Chassis Dimensions 1.73 x 17.5 x 11.3 in 4.4 x 44.5 x 28.8 cm Product number Product description C9200L-24T-4X-A Catalyst 9200L 24-port Data 4x10G uplink Switch, Network Advantage C9200L-24T-4X-E Catalyst 9200L 24-port Data 4x10G uplink Switch, Network Essentials C9200L-24P-4X-A Catalyst 9200L 24-port PoE+ 4x10G uplink Switch, Network Advantage C9200L-24P-4X-E Catalyst 9200L 24-port PoE+ 4x10G uplink Switch, Network Essentials Our stock support good price C9115AXI-E Specification Description Cisco Catalyst 9115AX Series Access Point, Internal antenna, Wi-Fi 6, 4x4:4 MIMO, E Domain Software в—Џ Cisco Unified Wireless Network Software Release 8.9 or later в—Џ Cisco IOS XE Software Release 16.11 or later Supported wireless LAN controllers в—Џ Cisco Catalyst 9800 Series Wireless Controllers в—Џ Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco Virtual Wireless Controller 802.11n version 2.0 (and related) capabilities в—Џ 4x4 MIMO with four spatial streams в—Џ Maximal Ratio Combining (MRC) в—Џ 802.11n and 802.11a/g beamforming в—Џ 20- and 40-MHz channels в—Џ PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 Dynamic Frequency Selection (DFS) в—Џ Cyclic Shift Diversity (CSD) support 802.11ac в—Џ 4x4 downlink MU-MIMO with four spatial streams в—Џ MRC в—Џ 802.11ac beamforming в—Џ 20-, 40-, 80-, and 160-MHz channels в—Џ PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 DFS в—Џ CSD support 802.11ax в—Џ 4x4 downlink MU-MIMO with four spatial streams в—Џ Uplink/downlink OFDMA в—Џ TWT в—Џ BSS coloring в—Џ MRC в—Џ 802.11ax beamforming в—Џ 20-, 40-, 80-, and 160-MHz channels в—Џ PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 DFS в—Џ CSD support Integrated antenna в—Џ 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in azimuth в—Џ 5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuth External antenna (sold separately) в—Џ Cisco Catalyst 9115AXE Access Points are certified for use with antenna gains up to 6 dBi (2.4 GHz and 5 GHz) в—Џ Cisco offers the industrys broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios Interfaces в—Џ 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) IEEE 802.3bz в—Џ Management console port (RJ-45) в—Џ USB 2.0 (enabled via future software) Indicators в—Џ Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors Dimensions (W x L x H) в—Џ Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5 in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x 20.3 x 4.3 cm) Input power requirements в—Џ 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal PoE (Cisco UPOE+, Cisco UPOE ) в—Џ Cisco power injector, AIR-PWRINJ6= в—Џ 802.3af PoE в—Џ Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af) Note: When 802.3af PoE is the source of power, both 2.4-GHz and 5-GHz radios will be reduced to 2x2 and Ethernet downgraded to 1 Gigabit Ethernet. In addition, the USB port will be off. Environmental Cisco Catalyst 9115AXI в—Џ Nonoperating (storage) temperature: -22 to 158F (-30 to 70C) в—Џ Nonoperating (storage) altitude test: 25ЛљC, 15,000 ft. в—Џ Operating temperature: 32 to 122F (0 to 50C) в—Џ Operating humidity: 10% to 90% (noncondensing) в—Џ Operating altitude test: 40ЛљC, 9843 ft. Note: When the ambient operating temperature exceeds 40C, the access point will shift from 4x4 to 2x2 on both the 2.4-GHz and 5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet, and the USB interface will be disabled. Cisco Catalyst 9115AXE в—Џ Nonoperating (storage) temperature: -22 to 158F (-30 to 70C) в—Џ Nonoperating (storage) altitude test: 25ЛљC, 15,000 ft. в—Џ Operating temperature: -4 to 122F (-20 to 50C) в—Џ Operating humidity: 10% to 90% (noncondensing) в—Џ Operating altitude test: 40ЛљC, 9843 ft. System memory в—Џ 2048 MB DRAM в—Џ 1024 MB flash Available transmit power settings 2.4 GHz в—Џ 23 dBm (200 mW) в—Џ 20 dBm (100 mW) в—Џ 17 dBm (50 mW) в—Џ 14 dBm (25 mW) в—Џ 11 dBm (12.5 mW) в—Џ 8 dBm (6.25 mW) в—Џ 5 dBm (3.13 mW) в—Џ 2 dBm (1.56 mW) в—Џ -1dBm (0.79mW) в—Џ -4dBm (0.39mW) 5 GHz в—Џ 23 dBm (200 mW) в—Џ 20 dBm (100 mW) в—Џ 17 dBm (50 mW) в—Џ 14 dBm (25 mW) в—Џ 11 dBm (12.5 mW) в—Џ 8 dBm (6.25 mW) в—Џ 5 dBm (3.13 mW) в—Џ 2 dBm (1.56 mW) в—Џ -1dBm (0.79mW) в—Џ -4dBm (0.39mW) Frequency band and 20-MHz operating channels E (E regulatory domain): в—Џ 2.412 to 2.472 GHz, 13 channels в—Џ 5.180 to 5.320 GHz, 8 channels в—Џ 5.500 to 5.700 GHz, 8 channels (excludes 5.600 to 5.640 GHz) C9115AXI-E Specification Description Cisco Catalyst 9115AX Series Access Point, Internal antenna, Wi-Fi 6, 4x4:4 MIMO, E Domain Software в—Џ Cisco Unified Wireless Network Software Release 8.9 or later в—Џ Cisco IOS XE Software Release 16.11 or later Supported wireless LAN controllers в—Џ Cisco Catalyst 9800 Series Wireless Controllers в—Џ Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco Virtual Wireless Controller 802.11n version 2.0 (and related) capabilities в—Џ 4x4 MIMO with four spatial streams в—Џ Maximal Ratio Combining (MRC) в—Џ 802.11n and 802.11a/g beamforming в—Џ 20- and 40-MHz channels в—Џ PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 Dynamic Frequency Selection (DFS) в—Џ Cyclic Shift Diversity (CSD) support 802.11ac в—Џ 4x4 downlink MU-MIMO with four spatial streams в—Џ MRC в—Џ 802.11ac beamforming в—Џ 20-, 40-, 80-, and 160-MHz channels в—Џ PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 DFS в—Џ CSD support 802.11ax в—Џ 4x4 downlink MU-MIMO with four spatial streams в—Џ Uplink/downlink OFDMA в—Џ TWT в—Џ BSS coloring в—Џ MRC в—Џ 802.11ax beamforming в—Џ 20-, 40-, 80-, and 160-MHz channels в—Џ PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 DFS в—Џ CSD support Integrated antenna в—Џ 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in azimuth в—Џ 5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuth External antenna (sold separately) в—Џ Cisco Catalyst 9115AXE Access Points are certified for use with antenna gains up to 6 dBi (2.4 GHz and 5 GHz) в—Џ Cisco offers the industrys broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios Interfaces в—Џ 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) IEEE 802.3bz в—Џ Management console port (RJ-45) в—Џ USB 2.0 (enabled via future software) Indicators в—Џ Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors Dimensions (W x L x H) в—Џ Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5 in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x 20.3 x 4.3 cm) Input power requirements в—Џ 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal PoE (Cisco UPOE+, Cisco UPOE ) в—Џ Cisco power injector, AIR-PWRINJ6= в—Џ 802.3af PoE в—Џ Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af) Note: When 802.3af PoE is the source of power, both 2.4-GHz and 5-GHz radios will be reduced to 2x2 and Ethernet downgraded to 1 Gigabit Ethernet. In addition, the USB port will be off. Environmental Cisco Catalyst 9115AXI в—Џ Nonoperating (storage) temperature: -22 to 158F (-30 to 70C) в—Џ Nonoperating (storage) altitude test: 25ЛљC, 15,000 ft. в—Џ Operating temperature: 32 to 122F (0 to 50C) в—Џ Operating humidity: 10% to 90% (noncondensing) в—Џ Operating altitude test: 40ЛљC, 9843 ft. Note: When the ambient operating temperature exceeds 40C, the access point will shift from 4x4 to 2x2 on both the 2.4-GHz and 5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet, and the USB interface will be disabled. Cisco Catalyst 9115AXE в—Џ Nonoperating (storage) temperature: -22 to 158F (-30 to 70C) в—Џ Nonoperating (storage) altitude test: 25ЛљC, 15,000 ft. в—Џ Operating temperature: -4 to 122F (-20 to 50C) в—Џ Operating humidity: 10% to 90% (noncondensing) в—Џ Operating altitude test: 40ЛљC, 9843 ft. System memory в—Џ 2048 MB DRAM в—Џ 1024 MB flash Available transmit power settings 2.4 GHz в—Џ 23 dBm (200 mW) в—Џ 20 dBm (100 mW) в—Џ 17 dBm (50 mW) в—Џ 14 dBm (25 mW) в—Џ 11 dBm (12.5 mW) в—Џ 8 dBm (6.25 mW) в—Џ 5 dBm (3.13 mW) в—Џ 2 dBm (1.56 mW) в—Џ -1dBm (0.79mW) в—Џ -4dBm (0.39mW) 5 GHz в—Џ 23 dBm (200 mW) в—Џ 20 dBm (100 mW) в—Џ 17 dBm (50 mW) в—Џ 14 dBm (25 mW) в—Џ 11 dBm (12.5 mW) в—Џ 8 dBm (6.25 mW) в—Џ 5 dBm (3.13 mW) в—Џ 2 dBm (1.56 mW) в—Џ -1dBm (0.79mW) в—Џ -4dBm (0.39mW) Frequency band and 20-MHz operating channels E (E regulatory domain): в—Џ 2.412 to 2.472 GHz, 13 channels в—Џ 5.180 to 5.320 GHz, 8 channels в—Џ 5.500 to 5.700 GHz, 8 channels (excludes 5.600 to 5.640 GHz) C9115AXI-E Specification Description Cisco Catalyst 9115AX Series Access Point, Internal antenna, Wi-Fi 6, 4x4:4 MIMO, E Domain Software в—Џ Cisco Unified Wireless Network Software Release 8.9 or later в—Џ Cisco IOS XE Software Release 16.11 or later Supported wireless LAN controllers в—Џ Cisco Catalyst 9800 Series Wireless Controllers в—Џ Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco Virtual Wireless Controller 802.11n version 2.0 (and related) capabilities в—Џ 4x4 MIMO with four spatial streams в—Џ Maximal Ratio Combining (MRC) в—Џ 802.11n and 802.11a/g beamforming в—Џ 20- and 40-MHz channels в—Џ PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 Dynamic Frequency Selection (DFS) в—Џ Cyclic Shift Diversity (CSD) support 802.11ac в—Џ 4x4 downlink MU-MIMO with four spatial streams в—Џ MRC в—Џ 802.11ac beamforming в—Џ 20-, 40-, 80-, and 160-MHz channels в—Џ PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 DFS в—Џ CSD support 802.11ax в—Џ 4x4 downlink MU-MIMO with four spatial streams в—Џ Uplink/downlink OFDMA в—Џ TWT в—Џ BSS coloring в—Џ MRC в—Џ 802.11ax beamforming в—Џ 20-, 40-, 80-, and 160-MHz channels в—Џ PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) в—Џ Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) в—Џ 802.11 DFS в—Џ CSD support Integrated antenna в—Џ 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in azimuth в—Џ 5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuth External antenna (sold separately) в—Џ Cisco Catalyst 9115AXE Access Points are certified for use with antenna gains up to 6 dBi (2.4 GHz and 5 GHz) в—Џ Cisco offers the industrys broadest selection of antennas, delivering optimal coverage for a variety of deployment scenarios Interfaces в—Џ 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) IEEE 802.3bz в—Џ Management console port (RJ-45) в—Џ USB 2.0 (enabled via future software) Indicators в—Џ Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors Dimensions (W x L x H) в—Џ Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5 in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x 20.3 x 4.3 cm) Input power requirements в—Џ 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal PoE (Cisco UPOE+, Cisco UPOE ) в—Џ Cisco power injector, AIR-PWRINJ6= в—Џ 802.3af PoE в—Џ Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af) Note: When 802.3af PoE is the source of power, both 2.4-GHz and 5-GHz radios will be reduced to 2x2 and Ethernet downgraded to 1 Gigabit Ethernet. In addition, the USB port will be off. Environmental Cisco Catalyst 9115AXI в—Џ Nonoperating (storage) temperature: -22 to 158F (-30 to 70C) в—Џ Nonoperating (storage) altitude test: 25ЛљC, 15,000 ft. в—Џ Operating temperature: 32 to 122F (0 to 50C) в—Џ Operating humidity: 10% to 90% (noncondensing) в—Џ Operating altitude test: 40ЛљC, 9843 ft. Note: When the ambient operating temperature exceeds 40C, the access point will shift from 4x4 to 2x2 on both the 2.4-GHz and 5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet, and the USB interface will be disabled. Cisco Catalyst 9115AXE в—Џ Nonoperating (storage) temperature: -22 to 158F (-30 to 70C) в—Џ Nonoperating (storage) altitude test: 25ЛљC, 15,000 ft. в—Џ Operating temperature: -4 to 122F (-20 to 50C) в—Џ Operating humidity: 10% to 90% (noncondensing) в—Џ Operating altitude test: 40ЛљC, 9843 ft. System memory в—Џ 2048 MB DRAM в—Џ 1024 MB flash Available transmit power settings 2.4 GHz в—Џ 23 dBm (200 mW) в—Џ 20 dBm (100 mW) в—Џ 17 dBm (50 mW) в—Џ 14 dBm (25 mW) в—Џ 11 dBm (12.5 mW) в—Џ 8 dBm (6.25 mW) в—Џ 5 dBm (3.13 mW) в—Џ 2 dBm (1.56 mW) в—Џ -1dBm (0.79mW) в—Џ -4dBm (0.39mW) 5 GHz в—Џ 23 dBm (200 mW) в—Џ 20 dBm (100 mW) в—Џ 17 dBm (50 mW) в—Џ 14 dBm (25 mW) в—Џ 11 dBm (12.5 mW) в—Џ 8 dBm (6.25 mW) в—Џ 5 dBm (3.13 mW) в—Џ 2 dBm (1.56 mW) в—Џ -1dBm (0.79mW) в—Џ -4dBm (0.39mW) Frequency band and 20-MHz operating channels E (E regulatory domain): в—Џ 2.412 to 2.472 GHz, 13 channels в—Џ 5.180 to 5.320 GHz, 8 channels в—Џ 5.500 to 5.700 GHz, 8 channels (excludes 5.600 to 5.640 GHz) C1000-48P-4G-L C9500-NM-8X CAB-SPWR-30CM C1000-48T-4G-L C9800-F-X-K9 C9200L-STACK-KIT WS-C2960X-24TS-LL N9K-C93180YC-FX PWR-C4-950WAC-R WS-C2960X-24PSQ-L N3K-C3172PQ-XL C9200-NM-4G WS-C2960X-24PS-L N2K-C2348UPQ C9200-NM-4X WS-C2960X-48TS-L AIR-AP1832I-H-K9 C9300-NM-4G WS-C2960L-24PS-AP AIR-AP2802I-H-K9 C9300-NM-8X WS-C2960L-16TS-LL C9115AXI-H GLC-LH-SMD WS-C2960L-8TS-LL C9120AXI-H SFP-10G-SR WS-C3560-48FS-S AIR-AP1562I-H-K9 SFP-10G-LR WS-C2960X-24PS-L AIR-AP1562D-H-K9 SFP-10G-SR-S C9200L-48P-4X-E C9800-L-C-K9 SFP-10G-LR-S C9200L-48P-4G-E C9800-L-F-K9 GLC-TE C9200L-24T-4G-E AP505 SFP-H10GB-CU2M C9300-24T-A AP515 MA-CBL-40G-3M C9300-48T-A CP-3905 GLC-LH-SMD= C9300-24S-A CP-7821-K9 ISR4331/K9 C9300-48S-A CP-8832-MIC-WIRED ISR4331/K9 RF C9300-48P-E CS-MIC-TABLE-J FPR2110-ASA-K9 C9300-24P-E AIR-AP3802I-E-K9 FPR2110-ASA-K9 C9300L-24T-4G-E C1111-8P FPR2120-ASA-K9 C9300L-48T-4G-E PWR-C5-125WAC FPR2130-ASA-K9 C9300-NM-8X PWR-C5-1KWAC C9200-NM-4G= C9400-LC-24S PWR-C6-125WAC C9200-NM-4G= C9400-LC-48S STACK-T1-50CM C9200L-24P-4G-CE C9500-24Y4C-A STACK-T1-1M C9200L-24P-4G-CE C9500-48Y4C-A STACK-T1-3M C9200L-48P-4G-E
