Huawei OptiX OSN500 03052117 21E12 S-1.1 SFP MSTP OSN500 SDH Transmission Equipment Product Description: The OptiX OSN 500 is a packet-oriented new-generation multi-service customer premises equipment (CPE) optical transmission system, which is positioned at the access layer among Huaweis end-to-end multi-service transmission platform (MSTP) product series. This system is characterized by its low power consumption and compact structure. The OptiX OSN 500 supports multiprotocol label switching (MPLS), MPLS-transport profile (MPLS-TP), pseudo wire emulation edge-to-edge (PWE3), Ethernet, and ATM technologies. With these technologies, a pure PTN network can be provisioned. As the access layer equipment, the OptiX OSN 500 is networked with other OptiX OSN equipment to provide a complete solution covering the backbone layer, aggregation layer, and access layer. The complete solution meets 2G/3G/LTE base station backhaul and enterprise leased service access demands. 1.Appearance Item Description Appearance Board System control, switching, and timing boards: CSHD Packet processing boards: EF8F/EM6T/EM6F/CQ1/MD1 Auxiliary boards: FAN Power supply boards: PIU and UPM For services and ports supported by the preceding boards, see Table 1. Packet functions and features Service features QoS features Hardware-based OAM Carrier-class protection Clock synchronization Switching capacity 7.2 Gbit/s Equipment-level protection 1+1 protection for input power Fan protection (The failure in a single fan does not affect the operation of the other fans.) Intelligent fan speed adjustment Supports automatic adjustments of fan speeds based on the highest temperature of boards in the chassis. Management ports and auxiliary ports Port Type Description Connector External clock port 120-ohm external clock port, which can work in 2048 kbit/s or 2048 kHz mode RJ45 External time port/Port for monitoring an outdoor cabinet External time port: The equipment provides two external time input/output ports. Port for monitoring an outdoor cabinet: The equipment provides one port for monitoring and managing an outdoor cabinet. RJ45 Power supply port Two -48/-60 V DC power ports 4-pin terminal block NMS management port NMS port/NMS serial port, which connects to an NMS RJ45 Alarm input/output port 3-input/1-output alarm port RJ45 2.Product Features This section describes the equipment features in terms of architecture and technology. High Availability, Low Power Consumption, and Compact Structure The OptiX OSN 500 is a device used at the access layer, which features high availability, low power consumption, and compact structure. The OptiX OSN 500 supports: Network-level protection such as tunnel automatic protection switching (APS), PW APS, Multiple Spanning Tree Protocol (MSTP), Ethernet ring protection switching (ERPS), link aggregation group (LAG), Multi-Link Point-to-Point Protocol (ML-PPP), linear multiplex section protection (LMSP), and link-state pass through (LPT), to improve equipment reliability A maximum power consumption of 100 W, and a typical power consumption of only 35 W Dimensions (H x W x D) of 44 mm x 442 mm x 220 mm, and installation in a cabinet (including ETSI and 19-inch cabinets), on a wall or desk, or in an open rack Pure Packet Architecture and Multi-service Transmission The OptiX OSN 500 supports service bearing in the PTN domain. This solution evolves based on the service changes that take place due to radio mobile network evolution. Therefore, this solution can meet the transmission requirements of not only 2G and 3G networks, but also the future LTE and 4G networks. Specifically, the OptiX OSN 500 can process and transport ATM, Ethernet, MPLS, and MPLS-TP services. End-to-End Service Configuration, One-Click Commissioning, and One-Click Fault Locating (TP-Assist) Compared with legacy TDM networks, PTN networks have the following characteristics in terms of O&M: Lack of as many overhead bytes that indicate physical states of networks as TDM networks. When a fault occurs on a PTN network, no visual and fast indicator is available to locate the fault. Networking diversity and complication, which require powerful O&M capabilities To address these issues, the equipment uses the TP-Assist to provide more O&M means and simplify O&M operations for PTN networks during installation, commissioning, service configuration, fault locating, and routine maintenance. With the TP-Assist, PTN networks have the SDH-like O&M capabilities, which reduce the technical requirements for O&M personnel and improve O&M efficiency. Product Details: If you are interested, please let us know the specific model. We will provide the best service and the best price! Pr
