Huawei OptiX OSN3500 02113256-2 Silver Line STM-64/STM-16 level MSTP OSN3500 Subrack Product Description: OptiX OSN 3500 is mainly used at the convergence layer and backbone layer of the metropolitan area network (MAN).In TDM networking, can be networked with the other OptiX transmission equipment (the OptiX OSN 9560, OptiX OSN 9500, OptiX OSN 7500 II, OptiX OSN 7500, OptiXOSN 3500 II, OptiX OSN 2500, OptiX OSN 1500, OptiX OSN 500, and OptiX OSN 550) to optimize the carriers investment. With the packet switching technology, can constitute a packet data transmission network with the other OptiX transmission equipment to meet the requirement for bearing IP services. Can be flexibly networked with WDM equipment and Metro equipment. Can transparently transmit services over third-party Layer 2 networks, allowing end-to-end configuration and management. Specifications: Indicator and Specifications Description Dimensions (H x W x D) 722 mm x 497 mm x 295 mm Number of valid slots 15 for processing boards and 16 for interface boards Equipment capacity Packet 160 Gbit/s TDM 200 Gbit/s higher order cross-connections and 20 Gbit/s lower order cross-connections Service type supported SDH, PDH, ATM, CES, Ethernet , PCM, SAN, video and others Network topology Point-to-point, chain, star, ring, ring with chain, intersecting rings, tangent rings Backup and protection Network-level protection (packet) Tunnel 1:1/1+1 APS, PW 1:1/1+1 APS, packet linear MSP, LPT, MSTP, MRPS Network-level protection (TDM) SDH protection: subnet connection protection, linear MSP, ring MSP , DNI protection, shared-fiber virtual path protection, optical-path-shared MSP EoS protection: LCAS, LPT, STP/RSTP, MSTP, ERPS, RPR, VP-Ring/VC-Ring protection Device-level protection Packet: LAG, MC-LAG TDM: TPS, BPS, PPS, LAG, DLAG, 1+1 protection for ATM boards, 1+1 protection for wavelength conversion units 1+1 hot backup for cross-connect and timing units 1+1 hot backup for SCC units 1+1 hot backup for power input units 1:N protection for +3.3 V power supply of the board Intelligent fan Board protection modes under abnormal conditions Maintenance MPLS OAM CV, FFD, BDI, FDI, Ping, Traceroute MPLS TP OAM CC, RDI, AIS, LB, LT, LM (only single-ended LM), DM, TST, LCK, CSF (only PW CSF) ETH OAM (packet) Ethernet service OAM: CC, LB, LT, LM (only single-ended LM), DM (only two-way DM) Ethernet port OAM: OAM auto-discovery, link performance monitoring, remote loopback, fault detection, self-loop detection ETH OAM (TDM) Ethernet service OAM: CC, LB, LT, OAM_Ping Ethernet port OAM: OAM auto-discovery, link performance monitoring, remote loopback, fault detection, self-loop detection Synchronization Packet Physical-layer clock (SDH) Synchronous Ethernet IEEE 1588v2 CES ACR TDM Physical-layer clock (SDH) DCN Outband DCN HWECC, IP over DCC, OSI over DCC Inband DCN HWECC, IP TP-Assist Service configuration: supports end-to-end service configuration and automatic deployment of alarm management. Service commissioning: supports the one-click service connectivity test, one-click service performance test, and automatic test without any instrument. Routine maintenance: supports performance statistics and monitoring and E-Line and E-LAN service path visualization. Fault diagnosis: supports intelligent fault locating, IP ping response, and service loopback detection. Standard working voltage If the standard voltage of the input power is -48 V, the power voltage ranges from -38.4 V to -57.6 V. If the standard voltage of the input power is -60 V, the power voltage ranges from -48 V to -72 V. Installation method ETSI cabinet Equipment running environment Subrack temperature Long-time operation: 0C to 45C Short-time operation: -5C to +55C Subrack humidity (relatively) Long-time operation: 5-85% Short-time operation: 5-95% Reliability specifications System availability 0.9999964 Mean time to resolution (MTTR) 1 h Mean time between failures (MTBF) 31.83 years Product Details: If you are interested, please let us know the specific model. We will provide the best service and the best price! Pr
