4 Port Clear Channel T1/E1 HWIC Cisco Router High-Speed WAN Interface card HWIC-4T1/E1 HWIC-4T1/E1 Overview The Cisco 4-Port Clear Channel T1/E1 High-Speed WAN Interface Card provides n x T1/E1 connectivity in a compact form factor and reduces deployment and management costs for the Cisco 2800, 3800, 2900 and 3900 Series Integrated Services Routers. As more data and voice services are enabled in branch offices, the demand for WAN bandwidth increases accordingly. Multilink Point-to-Point Protocol (PPP) and Multilink Frame Relay enable customers to scale their leased lines from single T1/E1 to multiples of T1/E1, adding bandwidth as their needs increase. The Cisco 4-Port Clear Channel T1/E1 High-Speed WAN Interface Card (HWIC) integrates four T1/E1 ports in a singlewide HWIC to facilitate n x T1/E1 connectivity in a compact form factor. With the Cisco 4-Port Clear Channel T1/E1 HWIC with integrated channel service unit and data service unit (CSU/DSU), you can consolidate customer premises equipment (CPE). The modules support balanced and unbalanced E1 connectivity and conform to G.703 and G.704 standards for unframed and framed E1 modes. The module supports both T1 and E1 modes, selectable by software configuration. Features At-A-Glance 4 ports of RJ-48 connectors Cisco IOS Software configurable for T1 or E1 operation Integrated CSU/DSU per port Balanced or unbalanced E1 termination in the same module E1 unframed and framed modes (G.703 and G.704) Independent clocking for each port Multilink PPP or Multilink Frame Relay (FRF.16) for T1/E1 ports on the same module and across different modules HWIC-4T1/E1 Specification Cisco 4 Port Clear Channel T1/E1 High Speed WAN Interface Card(HWIC-4T1/E1) Manufacturer Cisco Part Number HWIC-4T1/E1 Device Type Expansion module Form factor Plug-in module Interfaces/Ports 4 x RJ-48C T1/E1 WAN Data Transfer Rate 1.54 Mbps T1 2.05 Mbps E1 Management Features Management Supported by Cisco WAN Access Performance Management System (WAPMS) Cisco CNS 2100 Series Intelligence Engine (IE2100) CiscoWorks Diagnostic Loopback Support E1 loopback modes Controller local loopback Interface local loopback T1 loopback modes Interface local loopback Interface remote loopback Controller local loopback Controller remote loopback CSU loopback modes for T1 CSU Data terminal equipment (DTE) loopback Network loopback Payload loopback Alarm Detection Yellow alarm: Receive/send from/to network Blue alarm: Receive alarm indication signal (AIS) from network Red alarm: Loss of network signal Relevant MIB Support RFC1406-MIB CISCO-ICSUDSU-MIB Signaling Debugging ISDN Q.921 and Q.931 decode All other previously existing applicable Cisco IOS Software debugs Dimensions (H x W x D) 0.75 x 3.08 x 4.74 in. (1.91 x 7.82 x 12.04 cm) Weight 0.20 lb (0.09kg) Operating Temperature 32 to 104F (0 to 40C) 14 to 131F (-10C to 55C when installed in the MWR-2941-DC) Relative Humidity 5 to 95% noncondensing Regulatory Compliance and Safety Telecom Compliance United States: FCC Part 68 and TIA-968A Canada: Industry Canada CS-03 European Union: TBR 4, TBR 12, and TBR 13 Australia: AS/ACIF S038 and AS/ACIF S016 Japan: JATE Gray Book Hong Kong: HKTA 2027 and HKTA 2015 Taiwan: IS6100 Singapore: IDA TS ISDN PRA Korea: MIC No.2004-15 Telecommunication Interface Industry Standards ITU-T G.703 G.704 G.706 G.823 ANSI T1.403 Safety United States: UL60950 Canada: C22.2 No.60950 Europe: EN60950 Australia and New Zealand: AS/NZS3260 and TS001 Other countries: IEC60950 Network Equipment Building Standards (NEBS) GR-63 GR-78 GR-1089-CORE Type 1/3 EMC Emissions and Immunity 47 CFR Part 15: CISPR22: 2005 EN300386: V1.3.3 : 2005 EN55022: 1994 [+ amd 1 2] EN55022: 1998 EN61000-3-2: 2000 [Inc amd 1 2] EN61000-3-3: 1995 [+ amd 1: 2001] ICES-003 Issue 4 : 2004 KN 22: 2005 VCCI: V-3/2006.04 CISPR24: 1997 [+ amd 1 2] EN300386: V1.3.3 : 2005 EN50082-1: 1992 EN50082-1: 1997 EN55024: 1998 [+ amd 1 2] EN61000-6-1: 2001 Related Products NIM-ES2-4= NIM-ES2-8= C2960X-STACK= PVDM4-32= PVDM4-64= PVDM4-128= C3850-NM-2-10G C3850-NM-4-1G C3850-NM-8-10G
